Leadpipe Holder
-
- Posts: 88
- Joined: Sat Aug 11, 2018 9:30 pm
Leadpipe Holder
Does anyone know of a good accessory for lead pipes to hold them? Are there any recommended cases? Also, I have seen the Edwards lead pipes come in clear plastic tubes. Just looking for some leads, thanks.
- BGuttman
- Posts: 6295
- Joined: Thu Mar 22, 2018 7:19 am
- Location: Cow Hampshire
Re: Leadpipe Holder
I think somebody talked about using lengths of 1/2" PVC pipe. I don't remember if it was on here or on TTF.
Bruce Guttman
Merrimack Valley Philharmonic Orchestra
"Almost Professional"
Merrimack Valley Philharmonic Orchestra
"Almost Professional"
- Matt K
- Verified
- Posts: 4240
- Joined: Tue Mar 20, 2018 10:34 pm
- Contact:
Re: Leadpipe Holder
PVC pipe is great, I'm not sure what I got last time I went but I picked up some that have threads that seem to work with Shires *and* Conn leadpipes... in other words, you don't just put the pipe in... but the threads actually screw into the PVC pipe itself so it doesn't move around. Need to check out Home Depot again for more of those...
-
- Posts: 726
- Joined: Thu May 10, 2018 4:24 pm
- Location: Chicago, IL
- Contact:
Re: Leadpipe Holder
Not sure if it would work, but the Protec sax neck bag might be right up your alley. Not sure which size, if any, would fit a lead pipe(s)
https://www.amazon.com/Protec-Storage-M ... way&sr=8-2
https://www.amazon.com/Protec-Storage-M ... way&sr=8-2
King 2b+
King 3b
King 3b(f)
Conn 79h
Kanstul 1585
Olds O-21 Marching Trombone (Flugabone)
King 3b
King 3b(f)
Conn 79h
Kanstul 1585
Olds O-21 Marching Trombone (Flugabone)
-
- Posts: 365
- Joined: Thu Mar 29, 2018 7:51 pm
- Location: Maryland
Re: Leadpipe Holder
Kanstul made their protectors from 1/2" Schedule 80 PVC pipe. (Available at Lowe's)
A short length of a junked inner slide tube also makes a great protector. Maybe check with your local tech for one ?
The auto parts store sells 5/8" heater hose by the foot. That works good, too.
Or, you can dig deep into your pocket for one of these: https://osmun.com/trombone-leadpipe-pouch/
A short length of a junked inner slide tube also makes a great protector. Maybe check with your local tech for one ?
The auto parts store sells 5/8" heater hose by the foot. That works good, too.
Or, you can dig deep into your pocket for one of these: https://osmun.com/trombone-leadpipe-pouch/
-
- Posts: 88
- Joined: Sat Aug 11, 2018 9:30 pm
Re: Leadpipe Holder
Thanks for the replies. I have considered the PVC route, however, I know I have seen some nice transparent holders (like a test tube). I might go the Osmun route, that case looks nice. The reason I ask, I had a set of leadpipes in an old Tupperware container that disappeared so I don't want a repeat once I get the new replacements.
-
- Posts: 370
- Joined: Sat May 12, 2018 2:51 am
- Location: Devon UK
Re: Leadpipe Holder
My K+H pipes are sold in a clear tube with end caps. Something like this... https://www.google.co.uk/search?ei=ZpLq ... 94f-j4-JJ4
- jbeatenbough
- Posts: 330
- Joined: Fri Dec 13, 2019 1:57 pm
- Location: Warner Robins, Georgia
Re: Leadpipe Holder
Anyone know the correct tap size to thread the inside of the schedule 80 pvc (like the ones from kanstul)?
John
Tenor:
King 2B Silvertone-DW 12CS
Shires 1Y,T47,Dual Valve-DW 6BL
Shires 7YLW screw bell, T08-25YC-DW 6BS
Kanstul 1555-DW 6BS
Alto:
Thomann TEB480L-Schilke 45B
Trumpet:
King Liberty Silvertone AB-Schilke M2C
King 600-Bach 7C
Tenor:
King 2B Silvertone-DW 12CS
Shires 1Y,T47,Dual Valve-DW 6BL
Shires 7YLW screw bell, T08-25YC-DW 6BS
Kanstul 1555-DW 6BS
Alto:
Thomann TEB480L-Schilke 45B
Trumpet:
King Liberty Silvertone AB-Schilke M2C
King 600-Bach 7C
-
- Posts: 234
- Joined: Sun Apr 22, 2018 9:32 am
- Location: Tulsa, OK
Re: Leadpipe Holder
For which brand of pipe? Edwards/Getzen?jbeatenbough wrote: ↑Wed Jan 22, 2020 7:19 pm Anyone know the correct tap size to thread the inside of the schedule 80 pvc (like the ones from kanstul)?
- sacfxdx
- Posts: 349
- Joined: Wed Apr 11, 2018 4:25 pm
- Location: North Georgia, US
Re: Leadpipe Holder
How about conn 88h .525 ? XO .571 bass ? Just thought I’d ask in case anyone knew.
Steve
- Matt K
- Verified
- Posts: 4240
- Joined: Tue Mar 20, 2018 10:34 pm
- Contact:
Re: Leadpipe Holder
Actually, .571 is the valve bore, though their marketing materials are admittedly quite confusing with regards to that. Unfortunately, I can't answer the question about their threads
- jbeatenbough
- Posts: 330
- Joined: Fri Dec 13, 2019 1:57 pm
- Location: Warner Robins, Georgia
Re: Leadpipe Holder
Hi Steve, I'll bring a set of calipers to the next practice.. for the .571, we would probably have to use 1/2" schedule 40 instead of 80 (it has a larger inner diameter). I'll take a shot at measuring the thread spacing too...
John
Tenor:
King 2B Silvertone-DW 12CS
Shires 1Y,T47,Dual Valve-DW 6BL
Shires 7YLW screw bell, T08-25YC-DW 6BS
Kanstul 1555-DW 6BS
Alto:
Thomann TEB480L-Schilke 45B
Trumpet:
King Liberty Silvertone AB-Schilke M2C
King 600-Bach 7C
Tenor:
King 2B Silvertone-DW 12CS
Shires 1Y,T47,Dual Valve-DW 6BL
Shires 7YLW screw bell, T08-25YC-DW 6BS
Kanstul 1555-DW 6BS
Alto:
Thomann TEB480L-Schilke 45B
Trumpet:
King Liberty Silvertone AB-Schilke M2C
King 600-Bach 7C
-
- Posts: 152
- Joined: Fri Mar 23, 2018 2:28 pm
Re: Leadpipe Holder
The look of the Osmun pouch reminded me of a cigar case. I’m not sure of the dimensions of leadpipes ( I just plug and play ) or of larger cigars ( I only go for smaller perfectos, but I know cigars can get very long ). Also small Pelican and Otter cases of some model may work as well as the more slim profile pistol cases!
-
- Posts: 1610
- Joined: Tue Jul 02, 2019 9:06 am
- Location: New Jersey
- Contact:
Re: Leadpipe Holder
I'll see if I can get the numbers off the plastic pipes that kanstul used for their leadpipe sleeves.
David S. - daveyboy37 from TTF
Bach 39, LT36B, 42BOF & 42T, King 2103 / 3b, Kanstul 1570CR & 1588CR, Yamaha YBL-612 RII, YBL-822G & YBL-830, Sterling 1056GHS Euphonium,
Livingston Symphony Orchestra NJ - Trombone
Bach 39, LT36B, 42BOF & 42T, King 2103 / 3b, Kanstul 1570CR & 1588CR, Yamaha YBL-612 RII, YBL-822G & YBL-830, Sterling 1056GHS Euphonium,
Livingston Symphony Orchestra NJ - Trombone
- jbeatenbough
- Posts: 330
- Joined: Fri Dec 13, 2019 1:57 pm
- Location: Warner Robins, Georgia
Re: Leadpipe Holder
The ones that came with the Kanstul 1555 are 1/2 schedule 80 and the threads are M16x1.5mm (in case anyone wants to make their own). The length of the two "factory" storage tubes I have are 8 7/8" and 8". I'm so far making mine at 9" as the longest leadpipe I have so far is 8 5/8".
We'll start a tracking spreadsheet with outer diameter and thread size of as many as we can determine = )
We'll start a tracking spreadsheet with outer diameter and thread size of as many as we can determine = )
John
Tenor:
King 2B Silvertone-DW 12CS
Shires 1Y,T47,Dual Valve-DW 6BL
Shires 7YLW screw bell, T08-25YC-DW 6BS
Kanstul 1555-DW 6BS
Alto:
Thomann TEB480L-Schilke 45B
Trumpet:
King Liberty Silvertone AB-Schilke M2C
King 600-Bach 7C
Tenor:
King 2B Silvertone-DW 12CS
Shires 1Y,T47,Dual Valve-DW 6BL
Shires 7YLW screw bell, T08-25YC-DW 6BS
Kanstul 1555-DW 6BS
Alto:
Thomann TEB480L-Schilke 45B
Trumpet:
King Liberty Silvertone AB-Schilke M2C
King 600-Bach 7C
-
- Posts: 1610
- Joined: Tue Jul 02, 2019 9:06 am
- Location: New Jersey
- Contact:
Re: Leadpipe Holder
I think all of Kanstul's leadpipe collars are the same size and thread, which is the same as Shires. The collar threading is wider than the pipe will ever be, so all leadpipes fit in the same tubes that kanstul made.
David S. - daveyboy37 from TTF
Bach 39, LT36B, 42BOF & 42T, King 2103 / 3b, Kanstul 1570CR & 1588CR, Yamaha YBL-612 RII, YBL-822G & YBL-830, Sterling 1056GHS Euphonium,
Livingston Symphony Orchestra NJ - Trombone
Bach 39, LT36B, 42BOF & 42T, King 2103 / 3b, Kanstul 1570CR & 1588CR, Yamaha YBL-612 RII, YBL-822G & YBL-830, Sterling 1056GHS Euphonium,
Livingston Symphony Orchestra NJ - Trombone
- jbeatenbough
- Posts: 330
- Joined: Fri Dec 13, 2019 1:57 pm
- Location: Warner Robins, Georgia
Re: Leadpipe Holder
Cool. The ones I'm making are identical to the ones I got with the Kanstul, so they should hold anything but BASS leadpipes for Kanstul and Shires.
You do not have the required permissions to view the files attached to this post.
John
Tenor:
King 2B Silvertone-DW 12CS
Shires 1Y,T47,Dual Valve-DW 6BL
Shires 7YLW screw bell, T08-25YC-DW 6BS
Kanstul 1555-DW 6BS
Alto:
Thomann TEB480L-Schilke 45B
Trumpet:
King Liberty Silvertone AB-Schilke M2C
King 600-Bach 7C
Tenor:
King 2B Silvertone-DW 12CS
Shires 1Y,T47,Dual Valve-DW 6BL
Shires 7YLW screw bell, T08-25YC-DW 6BS
Kanstul 1555-DW 6BS
Alto:
Thomann TEB480L-Schilke 45B
Trumpet:
King Liberty Silvertone AB-Schilke M2C
King 600-Bach 7C
- muschem
- Posts: 238
- Joined: Sun Jan 17, 2021 10:16 am
- Location: Austin, Texas
- Contact:
Re: Leadpipe Holder
I love finding projects like these! This is a creative solution, and easy enough to DIY in a few minutes. I had some 1/2" schedule 80 PVC laying around, and so I gave this a whirl. I used an Edwards/Getzen threaded .508 leadpipe as a test, and for that collar, the M16x1.5mm turned out to be too small. The closest tap I had on hand that seemed to work was an M18x1.5mm. I'll be making more of these as I grow my collection of horns/leadpipes again.
-
- Posts: 1269
- Joined: Sat Mar 24, 2018 11:46 am
- Location: Vancouver WA
Re: Leadpipe Holder
TAP Plastics sells acrylic tubing and caps: https://www.tapplastics.com/product/pla ... bes_shapes
I made some out of PVC and cut them to size. (Sometimes I just want to be cheap. ) I used friction-fit caps, glued on one end. I left the other end un-glued. I also drilled holes at each end for ventilation.
I made some out of PVC and cut them to size. (Sometimes I just want to be cheap. ) I used friction-fit caps, glued on one end. I left the other end un-glued. I also drilled holes at each end for ventilation.
Kenneth Biggs
I have known a great many troubles, but most of them have never happened.
—Mark Twain (attributed)
I have known a great many troubles, but most of them have never happened.
—Mark Twain (attributed)
- jbeatenbough
- Posts: 330
- Joined: Fri Dec 13, 2019 1:57 pm
- Location: Warner Robins, Georgia
Re: Leadpipe Holder
I tried selling some that I made on here (to pay myself back the cost of the 20' pvc and the tap), but nobody was interested (even when cheap)... LOL
John
Tenor:
King 2B Silvertone-DW 12CS
Shires 1Y,T47,Dual Valve-DW 6BL
Shires 7YLW screw bell, T08-25YC-DW 6BS
Kanstul 1555-DW 6BS
Alto:
Thomann TEB480L-Schilke 45B
Trumpet:
King Liberty Silvertone AB-Schilke M2C
King 600-Bach 7C
Tenor:
King 2B Silvertone-DW 12CS
Shires 1Y,T47,Dual Valve-DW 6BL
Shires 7YLW screw bell, T08-25YC-DW 6BS
Kanstul 1555-DW 6BS
Alto:
Thomann TEB480L-Schilke 45B
Trumpet:
King Liberty Silvertone AB-Schilke M2C
King 600-Bach 7C
- Matt K
- Verified
- Posts: 4240
- Joined: Tue Mar 20, 2018 10:34 pm
- Contact:
Re: Leadpipe Holder
Dang really? Did yours have threads? I might be interested if I can screw some of my spares in if I can screw them in.jbeatenbough wrote: ↑Mon Oct 18, 2021 11:40 am I tried selling some that I made on here (to pay myself back the cost of the 20' pvc and the tap), but nobody was interested (even when cheap)... LOL
- jbeatenbough
- Posts: 330
- Joined: Fri Dec 13, 2019 1:57 pm
- Location: Warner Robins, Georgia
Re: Leadpipe Holder
Yes, threaded for kanstul and shires. I used 1/2 schedule 80 like kanstul did. The downside of 1/2 pvc is they won't fit .547 pipes. They will handle .500, .508, .525,....
I'm planning to make some using a bit larger pvc for my .547 pipes.
I'm planning to make some using a bit larger pvc for my .547 pipes.
John
Tenor:
King 2B Silvertone-DW 12CS
Shires 1Y,T47,Dual Valve-DW 6BL
Shires 7YLW screw bell, T08-25YC-DW 6BS
Kanstul 1555-DW 6BS
Alto:
Thomann TEB480L-Schilke 45B
Trumpet:
King Liberty Silvertone AB-Schilke M2C
King 600-Bach 7C
Tenor:
King 2B Silvertone-DW 12CS
Shires 1Y,T47,Dual Valve-DW 6BL
Shires 7YLW screw bell, T08-25YC-DW 6BS
Kanstul 1555-DW 6BS
Alto:
Thomann TEB480L-Schilke 45B
Trumpet:
King Liberty Silvertone AB-Schilke M2C
King 600-Bach 7C
- BGuttman
- Posts: 6295
- Joined: Thu Mar 22, 2018 7:19 am
- Location: Cow Hampshire
Re: Leadpipe Holder
You may want to consider Schedule 40 pipe. The OD is the same but the wall thickness is thinner The wall thickness of Schedule 80 1/2" pipe is about 0.140" while the wall thickness of Schedule 40 1/2" pipe is about 0.110"jbeatenbough wrote: ↑Tue Oct 19, 2021 9:43 am Yes, threaded for kanstul and shires. I used 1/2 schedule 80 like kanstul did. The downside of 1/2 pvc is they won't fit .547 pipes. They will handle .500, .508, .525,....
I'm planning to make some using a bit larger pvc for my .547 pipes.
Bruce Guttman
Merrimack Valley Philharmonic Orchestra
"Almost Professional"
Merrimack Valley Philharmonic Orchestra
"Almost Professional"
- jbeatenbough
- Posts: 330
- Joined: Fri Dec 13, 2019 1:57 pm
- Location: Warner Robins, Georgia
Re: Leadpipe Holder
Yes, something like that... I originally was duplicating the ones that I had that came from Kanstul - and they were 1/2 sched 80. Can't tell the difference in the ones they made and the copies I made. This was fine for my 1555.
Now for the T47, I need to make something slightly bigger. I'll take a leadpipe with me to the store and see what I can find... I want them to be strong enough to make it really hard to bend a foot long piece, but still fit a .547 pipe inside. I'll post what I find.
Now for the T47, I need to make something slightly bigger. I'll take a leadpipe with me to the store and see what I can find... I want them to be strong enough to make it really hard to bend a foot long piece, but still fit a .547 pipe inside. I'll post what I find.
John
Tenor:
King 2B Silvertone-DW 12CS
Shires 1Y,T47,Dual Valve-DW 6BL
Shires 7YLW screw bell, T08-25YC-DW 6BS
Kanstul 1555-DW 6BS
Alto:
Thomann TEB480L-Schilke 45B
Trumpet:
King Liberty Silvertone AB-Schilke M2C
King 600-Bach 7C
Tenor:
King 2B Silvertone-DW 12CS
Shires 1Y,T47,Dual Valve-DW 6BL
Shires 7YLW screw bell, T08-25YC-DW 6BS
Kanstul 1555-DW 6BS
Alto:
Thomann TEB480L-Schilke 45B
Trumpet:
King Liberty Silvertone AB-Schilke M2C
King 600-Bach 7C
- Matt K
- Verified
- Posts: 4240
- Joined: Tue Mar 20, 2018 10:34 pm
- Contact:
Re: Leadpipe Holder
Ah shucks, most of the pipes I have are 547 and larger. That may have been where your market disconnect was. Seems like threaded pipes are more common on large bores & basses than they are on small bores.
-
- Posts: 138
- Joined: Tue Nov 06, 2018 10:50 am
- jbeatenbough
- Posts: 330
- Joined: Fri Dec 13, 2019 1:57 pm
- Location: Warner Robins, Georgia
Re: Leadpipe Holder
I've been told that the shires .547 pipes are threaded 11/16-18. I'm ordering a tap today! Then I'll be able to make .547 holders for shires/kanstul. Thanks for the answer goes to hornbuilder!
John
Tenor:
King 2B Silvertone-DW 12CS
Shires 1Y,T47,Dual Valve-DW 6BL
Shires 7YLW screw bell, T08-25YC-DW 6BS
Kanstul 1555-DW 6BS
Alto:
Thomann TEB480L-Schilke 45B
Trumpet:
King Liberty Silvertone AB-Schilke M2C
King 600-Bach 7C
Tenor:
King 2B Silvertone-DW 12CS
Shires 1Y,T47,Dual Valve-DW 6BL
Shires 7YLW screw bell, T08-25YC-DW 6BS
Kanstul 1555-DW 6BS
Alto:
Thomann TEB480L-Schilke 45B
Trumpet:
King Liberty Silvertone AB-Schilke M2C
King 600-Bach 7C
- jbeatenbough
- Posts: 330
- Joined: Fri Dec 13, 2019 1:57 pm
- Location: Warner Robins, Georgia
Re: Leadpipe Holder
11/16-18 is correct! I've made three for my own .547 Shires leadpipes...I would be glad to make some for other folks.
You do not have the required permissions to view the files attached to this post.
John
Tenor:
King 2B Silvertone-DW 12CS
Shires 1Y,T47,Dual Valve-DW 6BL
Shires 7YLW screw bell, T08-25YC-DW 6BS
Kanstul 1555-DW 6BS
Alto:
Thomann TEB480L-Schilke 45B
Trumpet:
King Liberty Silvertone AB-Schilke M2C
King 600-Bach 7C
Tenor:
King 2B Silvertone-DW 12CS
Shires 1Y,T47,Dual Valve-DW 6BL
Shires 7YLW screw bell, T08-25YC-DW 6BS
Kanstul 1555-DW 6BS
Alto:
Thomann TEB480L-Schilke 45B
Trumpet:
King Liberty Silvertone AB-Schilke M2C
King 600-Bach 7C
- Matt K
- Verified
- Posts: 4240
- Joined: Tue Mar 20, 2018 10:34 pm
- Contact:
Re: Leadpipe Holder
I’m definitely interested. Need to figure out how many pipes I have though this weekend. Want to send me an email or pm?
-
- Posts: 3888
- Joined: Fri Mar 23, 2018 9:54 pm
- Location: California
Re: Leadpipe Holder
So what tubing did you use? Schedule 40 PVC pipe? What is the I.D.? What threads do other manufacturers use for their leadpipes?jbeatenbough wrote: ↑Thu Oct 13, 2022 8:01 am 11/16-18 is correct! I've made three for my own .547 Shires leadpipes...I would be glad to make some for other folks.
- jbeatenbough
- Posts: 330
- Joined: Fri Dec 13, 2019 1:57 pm
- Location: Warner Robins, Georgia
Re: Leadpipe Holder
I used schedule 80 for the .500 pipes, but I'm using schedule 40 1/2 for the .547. ID is about .560 as I measure it.
I know Kanstul also used schedule 80 for their .500, because I have one. I previously had a BP42 .547 and it was in a schedule 40 1/2 when I got it, but I'm not sure it was from the manufacturer. That is all I have personal knowledge about.
The schedule 40 walls are not as thick, but still a 10" piece of 1/2 sch40 is very stiff, so I think it give pretty good protection...you would have to work pretty hard to bend a leadpipe inside one.
I know Kanstul also used schedule 80 for their .500, because I have one. I previously had a BP42 .547 and it was in a schedule 40 1/2 when I got it, but I'm not sure it was from the manufacturer. That is all I have personal knowledge about.
The schedule 40 walls are not as thick, but still a 10" piece of 1/2 sch40 is very stiff, so I think it give pretty good protection...you would have to work pretty hard to bend a leadpipe inside one.
You do not have the required permissions to view the files attached to this post.
John
Tenor:
King 2B Silvertone-DW 12CS
Shires 1Y,T47,Dual Valve-DW 6BL
Shires 7YLW screw bell, T08-25YC-DW 6BS
Kanstul 1555-DW 6BS
Alto:
Thomann TEB480L-Schilke 45B
Trumpet:
King Liberty Silvertone AB-Schilke M2C
King 600-Bach 7C
Tenor:
King 2B Silvertone-DW 12CS
Shires 1Y,T47,Dual Valve-DW 6BL
Shires 7YLW screw bell, T08-25YC-DW 6BS
Kanstul 1555-DW 6BS
Alto:
Thomann TEB480L-Schilke 45B
Trumpet:
King Liberty Silvertone AB-Schilke M2C
King 600-Bach 7C
-
- Posts: 1593
- Joined: Tue Mar 27, 2018 5:51 am
- Location: central Virginia
Re: Leadpipe Holder
Or, pan flute, upside down?
- ithinknot
- Posts: 1107
- Joined: Fri Jul 24, 2020 3:40 pm
Re: Leadpipe Holder
You mention above that the Kanstul small bore threads are M16x1.5... just looking at the numbers, and given that 11/16-18 is correct for the large bores, I'd guess that the official spec on the small threads might in fact be 5/8-18.jbeatenbough wrote: ↑Wed Oct 05, 2022 9:03 am I've been told that the shires .547 pipes are threaded 11/16-18. I'm ordering a tap today! Then I'll be able to make .547 holders for shires/kanstul. Thanks for the answer goes to hornbuilder!
(Over this sort of length the metric version would certainly be close enough to function.)
- jbeatenbough
- Posts: 330
- Joined: Fri Dec 13, 2019 1:57 pm
- Location: Warner Robins, Georgia
Re: Leadpipe Holder
I think you may be correct. I've noticed that the ones for small bore that I did at M16x1.5 are a little snug screwing the pipes in... They work, but I don't think it was the exactly correct thread. Good thing I wasn't tapping a slide
John
Tenor:
King 2B Silvertone-DW 12CS
Shires 1Y,T47,Dual Valve-DW 6BL
Shires 7YLW screw bell, T08-25YC-DW 6BS
Kanstul 1555-DW 6BS
Alto:
Thomann TEB480L-Schilke 45B
Trumpet:
King Liberty Silvertone AB-Schilke M2C
King 600-Bach 7C
Tenor:
King 2B Silvertone-DW 12CS
Shires 1Y,T47,Dual Valve-DW 6BL
Shires 7YLW screw bell, T08-25YC-DW 6BS
Kanstul 1555-DW 6BS
Alto:
Thomann TEB480L-Schilke 45B
Trumpet:
King Liberty Silvertone AB-Schilke M2C
King 600-Bach 7C
- muschem
- Posts: 238
- Joined: Sun Jan 17, 2021 10:16 am
- Location: Austin, Texas
- Contact:
Re: Leadpipe Holder
I ended up buying several of the Edwards clear acrylic holders to replace the pvc ones I made. Their threading is better than my attempts to hand tap pvc, and it's nice that one size fits all of their pipes, so you don't need different tubes for small bore, large bore, bass, etc. Edwards sells these for $12, which seems pretty reasonable if you don't want to DIY the pvc route.
One tip - I found that 22mm vinyl end caps (https://smile.amazon.com/dp/B08HHSZ1V3) work perfectly to fit over the non-threaded end of the Edwards tubes. Not a critical add-on, but nice to prevent dust/debris, depending on how you store or transport them. For long-term storage, the caps also fit over the leadpipe collar after it is threaded into the tube.
Here's a couple of pics of what those look like, if you haven't seen them:
https://drive.google.com/drive/folders/ ... share_link
One tip - I found that 22mm vinyl end caps (https://smile.amazon.com/dp/B08HHSZ1V3) work perfectly to fit over the non-threaded end of the Edwards tubes. Not a critical add-on, but nice to prevent dust/debris, depending on how you store or transport them. For long-term storage, the caps also fit over the leadpipe collar after it is threaded into the tube.
Here's a couple of pics of what those look like, if you haven't seen them:
https://drive.google.com/drive/folders/ ... share_link
- jbeatenbough
- Posts: 330
- Joined: Fri Dec 13, 2019 1:57 pm
- Location: Warner Robins, Georgia
Re: Leadpipe Holder
I like your labels too...looks very professional. I just wrote on mine with a sharpie...looking for my label maker now
John
Tenor:
King 2B Silvertone-DW 12CS
Shires 1Y,T47,Dual Valve-DW 6BL
Shires 7YLW screw bell, T08-25YC-DW 6BS
Kanstul 1555-DW 6BS
Alto:
Thomann TEB480L-Schilke 45B
Trumpet:
King Liberty Silvertone AB-Schilke M2C
King 600-Bach 7C
Tenor:
King 2B Silvertone-DW 12CS
Shires 1Y,T47,Dual Valve-DW 6BL
Shires 7YLW screw bell, T08-25YC-DW 6BS
Kanstul 1555-DW 6BS
Alto:
Thomann TEB480L-Schilke 45B
Trumpet:
King Liberty Silvertone AB-Schilke M2C
King 600-Bach 7C
- boneberg
- Posts: 177
- Joined: Sat Dec 19, 2020 12:39 pm
- Location: Brandenburg/Berlin
Re: Leadpipe Holder
Did I understand correctly, that ALL Shires have the same thread size, but need different PVC pipes (with different I.D.) because of the bore size?
I am looking for something like this for Shires .525, .547 and .562
John are you still making these things to sell?
Thanks!
I am looking for something like this for Shires .525, .547 and .562
John are you still making these things to sell?
Thanks!