What can I do with this Conn Director? Bad lacquer
-
- Posts: 130
- Joined: Sun Dec 30, 2018 2:28 am
- Location: Sydney, Australia
What can I do with this Conn Director? Bad lacquer
Hello,
I have this old Conn Director and I would like to do something to it to make it look nice.
How about stripping it, hand polishing and tyen just a brass znti tarnish
Clear coat from a rattle can?
Or is there a better way?
This is cost sensitive budget repair to make this, otherwise fine, instrument presentable.
I have this old Conn Director and I would like to do something to it to make it look nice.
How about stripping it, hand polishing and tyen just a brass znti tarnish
Clear coat from a rattle can?
Or is there a better way?
This is cost sensitive budget repair to make this, otherwise fine, instrument presentable.
You do not have the required permissions to view the files attached to this post.
-
- Posts: 1865
- Joined: Mon Mar 02, 2020 6:18 am
Re: What can I do with this Conn Director? Bad lacquer
Strip polish and leave it to patina.
- Burgerbob
- Posts: 5068
- Joined: Mon Apr 23, 2018 8:10 pm
- Location: LA
- Contact:
Re: What can I do with this Conn Director? Bad lacquer
Aidan Ritchie, LA area player and teacher
- Doug Elliott
- Posts: 3380
- Joined: Wed Mar 21, 2018 10:12 pm
- Location: Maryand
Re: What can I do with this Conn Director? Bad lacquer
But it looks like some serious pitting too.
"I know a thing or two because I've seen a thing or two."
-
- Posts: 130
- Joined: Sun Dec 30, 2018 2:28 am
- Location: Sydney, Australia
Re: What can I do with this Conn Director? Bad lacquer
It looks like green pitting in places.
The lacquer was either poor or something happened to the instrument.
The case is fine and the problems are not limited to where the case padding touches.
The lacquer was either poor or something happened to the instrument.
The case is fine and the problems are not limited to where the case padding touches.
-
- Posts: 1089
- Joined: Fri Dec 14, 2018 12:07 pm
- Contact:
Re: What can I do with this Conn Director? Bad lacquer
You do not have the required permissions to view the files attached to this post.
Brad Close Brass Instruments - brassmedic.com
-
- Posts: 1444
- Joined: Tue Jan 14, 2020 10:52 am
Re: What can I do with this Conn Director? Bad lacquer
With older instruments like that, customers sometimes just want the brass to develop an even (lacquer-free) patina. If you don’t mind a brushed finish, the instrument could be “scratch-brushed.” It is a soft-brass bristle that is placed on a buffing wheel. Because no buffing compound is used, it brushes off layers of lacquer and leaves a light brushed finish without chewing into the metal.
I have found that it “evens out” the finish if a horn has spotty lacquer coverage. It allows the finish to age more evenly than the stark contrast of spotty lacquer against no lacquer.
Those Conn Directors can be hit or miss as players. Yes there are a lot of bad ones out there. However, I occasionally come across one that is very good.
I have found that it “evens out” the finish if a horn has spotty lacquer coverage. It allows the finish to age more evenly than the stark contrast of spotty lacquer against no lacquer.
Those Conn Directors can be hit or miss as players. Yes there are a lot of bad ones out there. However, I occasionally come across one that is very good.
Brian D. Hinkley - Player, Teacher, Technician and Trombone Enthusiast
-
- Posts: 130
- Joined: Sun Dec 30, 2018 2:28 am
- Location: Sydney, Australia
Re: What can I do with this Conn Director? Bad lacquer
My aim here is to make it nice and then sell it since I just have too many bones at this stage.
Nobody wanted it so far as is and I don't want to throw it out.
Nobody wanted it so far as is and I don't want to throw it out.
Last edited by berntd on Mon Feb 20, 2023 9:53 pm, edited 1 time in total.
-
- Posts: 1444
- Joined: Tue Jan 14, 2020 10:52 am
Re: What can I do with this Conn Director? Bad lacquer
The cost of making it “nice” might far exceed the amount you will get for the horn. Maybe just aim to make it look “better” and see what you can get for it.
Brian D. Hinkley - Player, Teacher, Technician and Trombone Enthusiast
-
- Posts: 130
- Joined: Sun Dec 30, 2018 2:28 am
- Location: Sydney, Australia
Re: What can I do with this Conn Director? Bad lacquer
Exactly my concern as well. I just can't get myself to throw it out.
In its current state, I could not even give it away. Never mind that it is playable
In its current state, I could not even give it away. Never mind that it is playable
-
- Posts: 365
- Joined: Thu Mar 29, 2018 7:51 pm
- Location: Maryland
Re: What can I do with this Conn Director? Bad lacquer
Brass polish would clean the tarnish off of the bare areas, making it look a lot better.
I would do that, and then donate the horn to a school music program in Sydney.
The Conn Director is a good starter horn for a grade-school beginner, and I'd bet that the band director could find it an appreciative home.
I would do that, and then donate the horn to a school music program in Sydney.
The Conn Director is a good starter horn for a grade-school beginner, and I'd bet that the band director could find it an appreciative home.
-
- Posts: 121
- Joined: Sun Dec 26, 2021 11:45 am
- Location: Southern California
Re: What can I do with this Conn Director? Bad lacquer
Lots of threads on stripping finish here. I'd say strip it, polish it, and then sell/donate it. Polishing goes much better if you buy some polishing wheels (I put mine onto my drill press), and a pack of tripoli, white diamond, and red rouge. I was pretty amazed how my old school horn turned out. Just be aware that if this is newer than around 1960, removing the finish will be a bear. Earlier... heck ... hot water does a fair job.
-
- Posts: 130
- Joined: Sun Dec 30, 2018 2:28 am
- Location: Sydney, Australia
Re: What can I do with this Conn Director? Bad lacquer
The finish on this horn seems to be of dubious quality to start with as I have not seen another horn where it has so much random loss and pitting. Unless someone sparyed it with something that caused the damage.
-
- Posts: 1444
- Joined: Tue Jan 14, 2020 10:52 am
Re: What can I do with this Conn Director? Bad lacquer
I have seen many horns with pitting like that turned into attractive instruments. After stripping the lacquer, use sandpaper or emery cloth to “blend” the pitted areas with others. Continue with finer grits of sandpaper/emery cloth and finish with multiple grades of steel wool (coarse to fine). You will have an attractive instrument with a raw brushed finish.
The secret is to not be too aggressive on the severely pitted areas. The key word is to “blend“ those sections with the metal around it.
The secret is to not be too aggressive on the severely pitted areas. The key word is to “blend“ those sections with the metal around it.
Brian D. Hinkley - Player, Teacher, Technician and Trombone Enthusiast