Sturdy, hard-to-topple, or even DIY Trombone Stand?
- sirisobhakya
- Posts: 308
- Joined: Mon Jun 11, 2018 8:04 pm
- Location: Bangkok, Thailand
- Contact:
Sturdy, hard-to-topple, or even DIY Trombone Stand?
Any recommendation for a sturdy, hard-to-topple trombone stand? Or experience even make one yourself from parts?
I normally set the horn on the floor, or have it always held in my hand in risky situations (such as students running and playing around). However, since I just bought a new tenor horn, and I want to play it both, maybe even switching in the same song, I felt I need a trombone stand. Also I don't want my trombone to feel left out, since I already bought a stand for the tenor horn .
A shop I can go have K&M 14985, which should be enough for normal operations. However, my issue is: the band room is quite crowded. Also, when the band is not set up and there are spaces available, students (and sometimes alumni too!) always run and play around. Also, I am quite clumsy myself. Therefore, toppling is very likely, and I cannot afford that. The 149/9 seems to be more rigid, but I wonder if any model would be even more sturdy.
Also, since there are many broken music stands, and also drum stands that I can use as starting point for a DIY trombone stand, does anyone has experience building one your own? I once used a drum stand with a rug laid on it for protection; usable but not that stable since there is no support inside the bell.
I normally set the horn on the floor, or have it always held in my hand in risky situations (such as students running and playing around). However, since I just bought a new tenor horn, and I want to play it both, maybe even switching in the same song, I felt I need a trombone stand. Also I don't want my trombone to feel left out, since I already bought a stand for the tenor horn .
A shop I can go have K&M 14985, which should be enough for normal operations. However, my issue is: the band room is quite crowded. Also, when the band is not set up and there are spaces available, students (and sometimes alumni too!) always run and play around. Also, I am quite clumsy myself. Therefore, toppling is very likely, and I cannot afford that. The 149/9 seems to be more rigid, but I wonder if any model would be even more sturdy.
Also, since there are many broken music stands, and also drum stands that I can use as starting point for a DIY trombone stand, does anyone has experience building one your own? I once used a drum stand with a rug laid on it for protection; usable but not that stable since there is no support inside the bell.
Chaichan Wiriyaswat
Bangkok, Thailand
“Why did I buy so many horns when I only have one mouth…?”
Bangkok, Thailand
“Why did I buy so many horns when I only have one mouth…?”
- ghmerrill
- Posts: 620
- Joined: Mon Apr 02, 2018 4:41 pm
- Location: Central North Carolina
Re: Sturdy, hard-to-topple, or even DIY Trombone Stand?
I built a very sturdy trombone stand from a Hamilton music stand. I use it as my "permanent" practice stand at home. This is particularly easy since the Hamilton music stand and trombone stand are virtually identical except for the top of the tube that holds the music table. You can also buy (at low cost) some parts from Hamilton. But basically, if you have a hack saw, a rubber plunger, some sort of rubber/plastic table leg cap, and maybe a couple of other small parts (like hose clamps), you should be able to build a trombone stand from something similar.
Gary Merrill
Wessex EEb tuba
Mack Brass Compensating Euph
Amati Oval Euph
1924 Buescher 3-valve Eb tuba
Schiller American Heritage 7B clone bass trombone
DE LB K/K9/112 Lexan, Brass Ark MV50R
1947 Olds "Standard" trombone (Bach 12c)
Wessex EEb tuba
Mack Brass Compensating Euph
Amati Oval Euph
1924 Buescher 3-valve Eb tuba
Schiller American Heritage 7B clone bass trombone
DE LB K/K9/112 Lexan, Brass Ark MV50R
1947 Olds "Standard" trombone (Bach 12c)
- greenbean
- Posts: 1801
- Joined: Fri Mar 23, 2018 6:14 pm
- Location: San Francisco
Re: Sturdy, hard-to-topple, or even DIY Trombone Stand?
I have several K&M 14990 stands. They are great. This one:
https://www.hornguys.com/collections/tr ... bone-stand
https://www.hornguys.com/collections/tr ... bone-stand
Tom in San Francisco
Currently playing...
Bach Corp 16M
Many French horns
Currently playing...
Bach Corp 16M
Many French horns
-
- Posts: 647
- Joined: Fri Mar 23, 2018 5:47 am
- Location: Oklahoma City
Re: Sturdy, hard-to-topple, or even DIY Trombone Stand?
I built my own bass trombone stand out of a broken cymbal stand. I added a large plunger head and used a walking cane tip for the cap on the riser tube.sirisobhakya wrote: ↑Sun Jan 06, 2019 8:47 pm Also, since there are many broken music stands, and also drum stands that I can use as starting point for a DIY trombone stand, does anyone has experience building one your own? I once used a drum stand with a rug laid on it for protection; usable but not that stable since there is no support inside the bell.
Cheap, effective, and extremely stable. But, it's also heavy!
--Andy in OKC
-
- Posts: 1483
- Joined: Tue Mar 27, 2018 5:51 am
- Location: central Virginia
Re: Sturdy, hard-to-topple, or even DIY Trombone Stand?
I have two DIY stands, both are extremely stable.
One is a repurposed cymbal stand, with a crutch tip on top. $5 for the stand at a thrift shop, couldn't pass that up.
The other is a round plastic base from a floor fan I found in a dumpster. It turned out a plunger stick was a friction fit in the hole. So I turned the plunger around, cut the plunger hole all the way through and forced the stick through. Then I dipped it in Tool dip for a rubber coating on top.
One is a repurposed cymbal stand, with a crutch tip on top. $5 for the stand at a thrift shop, couldn't pass that up.
The other is a round plastic base from a floor fan I found in a dumpster. It turned out a plunger stick was a friction fit in the hole. So I turned the plunger around, cut the plunger hole all the way through and forced the stick through. Then I dipped it in Tool dip for a rubber coating on top.
-
- Posts: 2862
- Joined: Fri Mar 23, 2018 7:31 am
Re: Sturdy, hard-to-topple, or even DIY Trombone Stand?
If the room is really that active, a solid stand is just going to be something immovable to smash the horn against. The instrument should be in a hard case if it's not in your hand in that environment.
-
- Posts: 3508
- Joined: Fri Mar 23, 2018 9:54 pm
- Location: California
Re: Sturdy, hard-to-topple, or even DIY Trombone Stand?
hyperbolica wrote: ↑Mon Jan 07, 2019 6:16 am If the room is really that active, a solid stand is just going to be something immovable to smash the horn against. The instrument should be in a hard case if it's not in your hand in that environment.
Or, since the stand is immobile, it (and the trombone resting on it) will be in the way of - and likely a collision target for - all the clumsy oafs who stumble by. Put the trombone back in its case when you are not actively tending it in this environment.
-
- Posts: 124
- Joined: Sun Apr 08, 2018 12:53 pm
- Location: DFW-Texas
Re: Sturdy, hard-to-topple, or even DIY Trombone Stand?
Mount a couple of these on the classroom wall up above the student traffic so they don't get run into.
https://www.amazon.com/s/?ie=UTF8&keywo ... jy0s696g_b
https://www.amazon.com/s/?ie=UTF8&keywo ... jy0s696g_b
-
- Posts: 988
- Joined: Fri Mar 23, 2018 11:33 pm
Re: Sturdy, hard-to-topple, or even DIY Trombone Stand?
I like that. A round base makes it unlikely to tip in any direction. My stands have five legs, which is good for the same reason.timothy42b wrote: ↑Mon Jan 07, 2019 5:51 am ...
The other is a round plastic base from a floor fan I found in a dumpster. It turned out a plunger stick was a friction fit in the hole. So I turned the plunger around, cut the plunger hole all the way through and forced the stick through. Then I dipped it in Tool dip for a rubber coating on top.
- BillO
- Posts: 112
- Joined: Fri Mar 23, 2018 11:26 am
- Location: Deep woods of central Ontario
Re: Sturdy, hard-to-topple, or even DIY Trombone Stand?
I'll offer another vote for the K&M 14990. Best stand I have ever used. Have 3 now and will soon have 5 in order to replace my other 2 stands.greenbean wrote: ↑Sun Jan 06, 2019 9:16 pm I have several K&M 14990 stands. They are great. This one:
https://www.hornguys.com/collections/tr ... bone-stand
- Backbone
- Posts: 149
- Joined: Sun Apr 08, 2018 9:46 pm
Re: Sturdy, hard-to-topple, or even DIY Trombone Stand?
DYI:
Used a cymbal stand and added the in bell support from a traditional trombone stand. Super sturdy.
Used a cymbal stand and added the in bell support from a traditional trombone stand. Super sturdy.
Last edited by Backbone on Wed Jan 30, 2019 4:31 pm, edited 1 time in total.
-
- Posts: 368
- Joined: Mon Jan 07, 2019 8:56 pm
Re: Sturdy, hard-to-topple, or even DIY Trombone Stand?
I like my On-Stage stand; it's quite sturdy. The bell holder has pads on it, protecting the finish and enabling air to circulate in the bell so that moisture condensation doesn't get trapped inside by the holder itself. Hamilton makes a similar product.
Current instruments:
Olds Studio trombone, 3 trumpets, 1 flugelhorn, 1 cornet, 1 shofar, 1 keyboard
Previous trombones:
Selmer Bundy, Marceau
Olds Studio trombone, 3 trumpets, 1 flugelhorn, 1 cornet, 1 shofar, 1 keyboard
Previous trombones:
Selmer Bundy, Marceau
-
- Posts: 168
- Joined: Sat Jul 07, 2018 2:15 pm
Re: Sturdy, hard-to-topple, or even DIY Trombone Stand?
Like most kids in band, if the horn isn’t in your hands, it should be in your case. Unless other students are liable for your equipment, this isn’t a trombone stand issue.
Michael Lawson
Freelance Trombonist
Dallas - Ft. Worth, TX
Freelance Trombonist
Dallas - Ft. Worth, TX
-
- Posts: 614
- Joined: Fri Mar 23, 2018 9:44 am
- Location: Rochester Michigan North of Detroit.
- Contact:
Re: Sturdy, hard-to-topple, or even DIY Trombone Stand?
My home stand is screwed to the floor so the horns cannot slide into each other.
Wood dowels are set into a 2 x 6. Drill a hole the size of the dowel and sink a screw from the other side.
Then toilet plungers drilled out to fit the dowel are slid over with a hose clamp or a few screws below to hold them in place. And a rubber cap on the top.
Top with a decorative table cloth.
On the side I have two 2 x 6's with angled tops connected at a right angle. This makes a great hanger for trombone slides.
The euph is hanging on a hardware hook connected to a 2 x 6.
The Pbone is just leaning against the wall.
https://drive.google.com/file/d/0B1izx3 ... RWNm8/view
Wood dowels are set into a 2 x 6. Drill a hole the size of the dowel and sink a screw from the other side.
Then toilet plungers drilled out to fit the dowel are slid over with a hose clamp or a few screws below to hold them in place. And a rubber cap on the top.
Top with a decorative table cloth.
On the side I have two 2 x 6's with angled tops connected at a right angle. This makes a great hanger for trombone slides.
The euph is hanging on a hardware hook connected to a 2 x 6.
The Pbone is just leaning against the wall.
https://drive.google.com/file/d/0B1izx3 ... RWNm8/view
Edwards Sterling bell 525/547
Edwards brass bell 547/562
Edwards Jazz w/ Ab valve 500"/.508"
Markus Leuchter Alto Trombone
Bass Bach 50 Bb/F/C dependent.
Cerveny oval euphonium
Full list in profile
Edwards brass bell 547/562
Edwards Jazz w/ Ab valve 500"/.508"
Markus Leuchter Alto Trombone
Bass Bach 50 Bb/F/C dependent.
Cerveny oval euphonium
Full list in profile
-
- Posts: 2862
- Joined: Fri Mar 23, 2018 7:31 am
Re: Sturdy, hard-to-topple, or even DIY Trombone Stand?
The thing that makes me uncomfortable about this is that if someone bumps your horn, it's going to get damaged against the immovable stand.
The Hercules hand grip stand is definitely the most stable, and probably the safest overall, but it only accounts for asymmetry on one axis. It still allows the horn to spin on the hand grip if it isn't set right.
-
- Posts: 988
- Joined: Fri Mar 23, 2018 11:33 pm
Re: Sturdy, hard-to-topple, or even DIY Trombone Stand?
You do not have the required permissions to view the files attached to this post.
-
- Posts: 988
- Joined: Fri Mar 23, 2018 11:33 pm
Re: Sturdy, hard-to-topple, or even DIY Trombone Stand?
(For some reason, though the file on my drive is in portrait, it shows here in landscape. Why?)
You do not have the required permissions to view the files attached to this post.
-
- Posts: 413
- Joined: Fri Mar 23, 2018 2:19 pm
Re: Sturdy, hard-to-topple, or even DIY Trombone Stand?
Baileyman,
What stand is that? It’s the first trombone stand I’ve seen with five legs. I’ve always had a preference for the “heavy duty” K&M 14990, but I’m really interested in checking that one out.
Terry
-
- Posts: 126
- Joined: Sat Aug 25, 2018 8:33 pm
Re: Sturdy, hard-to-topple, or even DIY Trombone Stand?
Another +1 on the K&M 14990.
I’ve never felt the need to shop for anything else.
I’ve never felt the need to shop for anything else.
Getzen 3508 - Swanson Custom
Conn 88h - Elkhart
Minick Conn 62h - Elkhart
Besson New Standard Euphonium - MS
DE XT, SB Setups
Griego Markey 87
Conn 88h - Elkhart
Minick Conn 62h - Elkhart
Besson New Standard Euphonium - MS
DE XT, SB Setups
Griego Markey 87
- BGuttman
- Posts: 5994
- Joined: Thu Mar 22, 2018 7:19 am
- Location: Cow Hampshire
Re: Sturdy, hard-to-topple, or even DIY Trombone Stand?
That 5 legged stand is home-built. I know of only two: Baileyman's and an associate who plays in the same band. I've seen it plenty of times.
It's light. I wouldn't store a heavy bass trombone on it, but it's great for Baileyman's Bach 16 or Bach 12. And it's really stable.
It's light. I wouldn't store a heavy bass trombone on it, but it's great for Baileyman's Bach 16 or Bach 12. And it's really stable.
Bruce Guttman
Merrimack Valley Philharmonic Orchestra
"Almost Professional"
Merrimack Valley Philharmonic Orchestra
"Almost Professional"
-
- Posts: 988
- Joined: Fri Mar 23, 2018 11:33 pm
Re: Sturdy, hard-to-topple, or even DIY Trombone Stand?
[All messed up pics in post attempt, will retry.]
-
- Posts: 988
- Joined: Fri Mar 23, 2018 11:33 pm
Re: Sturdy, hard-to-topple, or even DIY Trombone Stand?
Here's a 50b with the weight to the sloping side, 18 degrees tip over point.
You do not have the required permissions to view the files attached to this post.
-
- Posts: 988
- Joined: Fri Mar 23, 2018 11:33 pm
Re: Sturdy, hard-to-topple, or even DIY Trombone Stand?
Here is a Bach 16 on standard geometry (three leg) stand, tipping point 13 degrees.
You do not have the required permissions to view the files attached to this post.
- trompanner
- Posts: 23
- Joined: Sat Feb 02, 2019 5:15 pm
Re: Sturdy, hard-to-topple, or even DIY Trombone Stand?
I too have this stand and I love it! Its the highest quality stand I've ever owned and I carry it everywhere with me. I used to have a Hamilton Stand (all chrome) but the joints of the legs on that one eventually broke and would longer stand without leaning or wobbling (thanks to clumsy private students stepping on them). I also had one of the Hercules In-Bell stands, and that one failed on me after about a year of use. I completely stand behind the K&M!greenbean wrote: ↑Sun Jan 06, 2019 9:16 pm I have several K&M 14990 stands. They are great. This one:
https://www.hornguys.com/collections/tr ... bone-stand