Page 3 of 4

Re: Joe Alessi

Posted: Wed Dec 04, 2019 2:51 pm
by ZacharyThornton
And the Q series are manufactured in China in US made parts.

Re: Joe Alessi

Posted: Wed Dec 04, 2019 7:45 pm
by elmsandr
tbonesullivan wrote: Wed Dec 04, 2019 11:18 am I have wondered why the tuning slides on the F-attachment are so long, even when an E-pull isn't possible or intended. Is it for stability reasons, or is it just cheaper to make them that way? Even Bass trombones have very long attachment tuning slides.
Conjecture: early F attachments didn’t have E pulls, they had short tuning slides. They decided an E pull was useful so they had really long tuning slides. Some messed with them and screwed up the length so there was no longer an E pull. Nobody used it, so they didn’t really miss it. Open wraps were first built from the same parts as those other wraps. Nobody really questioned it, thus we still have stupidly long F attachment pulls that don’t even get to E.

Changing that length does change how the horn blows and feels, and even different is different and not necessarily good, so who has really tried it?

Only horn I’ve ever had with shorter attachment slides is a Fuchs. Don’t know how that plays yet, still have work to do.

Cheers,
Andy

Re: Joe Alessi

Posted: Fri Dec 06, 2019 11:58 am
by mfellows821
Are the Q series parts the same parts used on the custom? If some are different , which ones? Gabe?

Re: Joe Alessi

Posted: Sun Dec 08, 2019 1:09 pm
by Mv2541
While the Q looks very similar to the regular horn, there are some obvious differences: valve cap and main tuning slide for starters. Anyone who has played an M&W will know how much the valve cap can change the horn, so this might not be as insignificant as some are bound to believe.

Re: Joe Alessi

Posted: Sun Dec 08, 2019 5:11 pm
by castrubone
Mv2541 wrote: Sun Dec 08, 2019 1:09 pm While the Q looks very similar to the regular horn, there are some obvious differences: valve cap and main tuning slide for starters. Anyone who has played an M&W will know how much the valve cap can change the horn, so this might not be as insignificant as some are bound to believe.
I don't think that's accurate. Maybe a Shires insider will have the scoop, but the descriptions are the same for the Q series and the full custom version. As with all Q series horns the difference lies in where it's manufactured.

Re: Joe Alessi

Posted: Sun Dec 08, 2019 9:40 pm
by harrisonreed
I still don't understand how "parts manufactured in MA, but assembled in China" makes sense for modular horns ...

I can assemble a modular horn in about two minutes for free.

Re: Joe Alessi

Posted: Sun Dec 08, 2019 10:04 pm
by Burgerbob
Think smaller parts. Bell flare, ferrules, braces, tubes.

Re: Joe Alessi

Posted: Sun Dec 08, 2019 11:59 pm
by Schlitz
.

Re: Joe Alessi

Posted: Mon Dec 09, 2019 12:45 am
by harrisonreed
Ahhh so it's the soldering and brazing, etc. Even attaching the flare onto the stem? Wow!

Re: Joe Alessi

Posted: Mon Dec 09, 2019 2:07 am
by Burgerbob
It is US parts assembled in China. US made bells, ferrules, tubes, etc. that are soldered into a trombone in China.

Re: Joe Alessi

Posted: Mon Dec 09, 2019 2:09 am
by harrisonreed
Got it!

Re: Joe Alessi

Posted: Mon Dec 09, 2019 6:15 am
by chromebone
So, in other words, do you want your horn assembled by a worker who is reasonably well paid, has good benefits and workplace safety requirements as set out by the state, or save a bunch of money and have one assembled by a worker that works for far less, probably lives in one of those factory dormitory cities that house thousands of workers and probably has little or no benefits and workplace safety requirements. Someone’s paying somewhere for that nice horn.

Re: Joe Alessi

Posted: Mon Dec 09, 2019 7:35 am
by timbone
What chromebone said. This is no different than the Iphone and Nike sweatshops. I've seen the dorms too - and those are the people that are taken care of! Just like Walmart says- "Save more, live better" .......

The bigger global problem is- its getting harder to find folks from younger generations that want to get their hands dirty. Who do we pass these skills onto? How many of your friends are ready to commit to a machine shop polishing brass when they can make so much more in an IT or technology job? Therefore it often goes to the lowest common denominator, or members of a caste system. If we don't compete dollar wise for competent labor in the market, we have to look elsewhere/offshore.

Re: Joe Alessi

Posted: Mon Dec 09, 2019 10:22 am
by tbonesullivan
Are ALL of the parts made in the U.S.? Even things like the drawn slide tubes? It also does seem that the parts of the Alessi horn that are for the Q series horn have different part numbers, so it's gotta be more than just the same parts assembled somewhere else. Of course, a lot of things are made by a CNC lathe these days, so it's not like it matters where it is done.

Re: Joe Alessi

Posted: Mon Dec 09, 2019 11:26 am
by Burgerbob
I assume they have a bit of a higher-output, slightly-lower-quality-even-if-they-say-it's-not side of the workshop at Shires that is doing the Q parts. But that's just my assumption.

Re: Joe Alessi

Posted: Mon Dec 09, 2019 2:18 pm
by JohnL
Burgerbob wrote: Mon Dec 09, 2019 11:26 am I assume they have a bit of a higher-output, slightly-lower-quality-even-if-they-say-it's-not side of the workshop at Shires that is doing the Q parts. But that's just my assumption.
I doubt it. Having two separate production setups is likely to end up being more expensive than producing everything together. That machine sitting on the factory floor is costing you money just sitting there. Even if it's fully bought and paid for, it's occupying space, and that space costs money - not to mention depreciation as the machine ages.

We know that the Q-series is assembled in China; how about the finishing processes? China or US? Some of the post-assembly processes are pretty labor-intensive.

Re: Joe Alessi

Posted: Tue Dec 10, 2019 1:21 am
by Schlitz
.

Re: Joe Alessi

Posted: Tue Dec 10, 2019 4:18 am
by harrisonreed
I just tweaked my harmonic bridge to help increase the resistance on my 396 for an upcoming gig that has a ton of playing and many big passages (when I'm not on my 3B for the big band charts). It's a new one for me to have someone asking for more trombone through the rehearsal, and the extra resistance and stability is really helpful to make that happen. I'm really glad I have that ability on my horn!

Re: Joe Alessi

Posted: Tue Dec 10, 2019 5:06 am
by SwissTbone
harrisonreed wrote: Tue Dec 10, 2019 4:18 am It's a new one for me to have someone asking for more trombone through the rehearsal, and the extra resistance and stability is really helpful to make that happen. I'm really glad I have that ability on my horn!
Try to keep that gig, sounds like a director who knows what he's talking about :-)

On a more serious note: Yes, that harmonic bridge makes a difference. I also played around a little with it those last days. There are a lot of options, so you gotta know what you do. But once you know wich pillar does what for you, you can really dial the trombone in for you.

Re: Joe Alessi

Posted: Tue Dec 10, 2019 11:07 am
by bcschipper
harrisonreed wrote: Tue Dec 10, 2019 4:18 am I just tweaked my harmonic bridge to help increase the resistance on my 396 for an upcoming gig that has a ton of playing and many big passages (when I'm not on my 3B for the big band charts). It's a new one for me to have someone asking for more trombone through the rehearsal, and the extra resistance and stability is really helpful to make that happen. I'm really glad I have that ability on my horn!
What do you mean exactly by "resistance"? Until now I thought it refers to the resistance of the airflow. I don't see how airflow could be affected by the harmonic bridge.

Re: Joe Alessi

Posted: Tue Dec 10, 2019 11:33 am
by tbonesullivan
The same kind of "resistance" you feel to trying to lip up or down a note. Resistance to vibration. The FEEL. It's pretty much impossible to quantify. However I feel that is the core of what makes different trombones different.

Re: Joe Alessi

Posted: Tue Dec 10, 2019 12:30 pm
by norbie2018
It sounds like you referring to response. Resistance usually refers to the amount of constriction felt against the air stream.

Re: Joe Alessi

Posted: Tue Dec 10, 2019 12:31 pm
by Burgerbob
norbie2018 wrote: Tue Dec 10, 2019 12:30 pm It sounds like you referring to response. Resistance usually refers to the amount of constriction felt against the air stream.
There's real air resistance, and then there's perceived resistance. Bracing can make a big difference to the latter.

Re: Joe Alessi

Posted: Tue Dec 10, 2019 1:25 pm
by harrisonreed
Yes ^ the answers above are what I think too.

I think somehow that the room is related to it as well. In a huge echo chamber, pretty much any horn will just about play itself. In a dead, stuffy room that is full of people somehow that same horn becomes dead and hard to play. That's usually when I find myself adding mass near the bell on the brace. Then suddenly I can get output again.

Re: Joe Alessi

Posted: Tue Dec 10, 2019 1:35 pm
by Burgerbob
Yup. My orchestral bass doesn't feel good in small spaces for just that reason.

Re: Joe Alessi

Posted: Tue Dec 10, 2019 1:37 pm
by SwissTbone
harrisonreed wrote: Tue Dec 10, 2019 1:25 pm Yes ^ the answers above are what I think too.

I think somehow that the room is related to it as well. In a huge echo chamber, pretty much any horn will just about play itself. In a dead, stuffy room that is full of people somehow that same horn becomes dead and hard to play. That's usually when I find myself adding mass near the bell on the brace. Then suddenly I can get output again.

Interesting observations.

Re: Joe Alessi

Posted: Tue Dec 10, 2019 1:52 pm
by harrisonreed
cozzagiorgi wrote: Tue Dec 10, 2019 1:37 pm
harrisonreed wrote: Tue Dec 10, 2019 1:25 pm Yes ^ the answers above are what I think too.

I think somehow that the room is related to it as well. In a huge echo chamber, pretty much any horn will just about play itself. In a dead, stuffy room that is full of people somehow that same horn becomes dead and hard to play. That's usually when I find myself adding mass near the bell on the brace. Then suddenly I can get output again.

Interesting observations.
Since you said you we're messing with a harmonic brace yourself, you can try what I've been using:

Ordinarily, I play with the copper "1" in the center hole, facing down, towards the bell. For this situation, I reversed the "1", so it is towards the tuning slide, and added the long copper closest to the bell, facing down, towards the bell. It is in only enough to be flush with the brace but not going through it. I usually wouldn't like that, but it works very well in a dead room.

Re: Joe Alessi

Posted: Tue Dec 10, 2019 2:28 pm
by bcschipper
O.k., thanks for the clarification. I call this "response".

Re: Joe Alessi

Posted: Tue Dec 10, 2019 2:54 pm
by tbonesullivan
I never understood "resistance" much. The smallest diameter portion of the horn is by far the mouthpiece throat. You also will never be really trying to put full airstream capacity through a horn. I mean, I feel resistance, but I don't know if it's any greater than just trying to blow through the mouthpiece by itself.

Re: Joe Alessi

Posted: Tue Dec 10, 2019 3:30 pm
by norbie2018
But the shape/taper of the leadpipe has a direct influence on the resistance as well.

Re: Joe Alessi

Posted: Tue Dec 10, 2019 4:18 pm
by Ndwood
You can think of it as two types of resistance: air resistance, and the resistance of the actual horn to vibration.

Re: Joe Alessi

Posted: Tue Dec 10, 2019 4:19 pm
by harrisonreed
I don't see how a three inch long pipe with a choke point of .27 inches could have the same amount of resistance as an 8 foot long pipe with a choke point of .27 inches.

The amount of air it would take to get a mouthpiece to push back on you and produce a harmonic series would be insane. That's why buzzing makes no sense to me. The amount of air and effort it takes to get a trombone to push back and produce a harmonic series is exponentially less. Because there is resistance in the horn.

Re: Joe Alessi

Posted: Tue Dec 10, 2019 4:25 pm
by Schlitz
.

Re: Joe Alessi

Posted: Tue Dec 10, 2019 4:29 pm
by Burgerbob
Schlitz wrote: Tue Dec 10, 2019 4:25 pm Joe doesn’t play this horn anymore.
Which horn would that be?

Re: Joe Alessi

Posted: Wed Dec 11, 2019 10:01 pm
by Mikebmiller
So maybe Mr. Alessi will be selling all his Edwards horns on the classifieds here soon.

Re: Joe Alessi

Posted: Thu Dec 12, 2019 3:06 am
by thetuningslide
I'm assuming I'll see you all at Midwest to try the alessi shires horn then?

Re: Joe Alessi

Posted: Thu Dec 12, 2019 5:26 pm
by harrisonreed
It would have to be a miracle of a horn to make me consider spending more money on instruments. Count me out haha

Re: Joe Alessi

Posted: Thu Dec 12, 2019 5:42 pm
by Schlitz
.

Re: Joe Alessi

Posted: Thu Dec 12, 2019 5:54 pm
by thetuningslide
I never liked the 396, so I doubt I'll love the shires 396. I have always loved shires bones tho, maybe it'll be perfect. I'm mostly trying it to say I've tried it, and to return to my college studio my findings.

Re: Joe Alessi

Posted: Wed Dec 18, 2019 9:38 am
by griffinben
GabeLangfur wrote: Tue Dec 03, 2019 7:25 am
Mv2541 wrote: Mon Dec 02, 2019 3:50 pm Something I noticed today: for the Shires Alessi wrap the air flows backwards from their normal rotors- not that it's a big deal, but I have to wonder why (or what was wrong with their normal wrap)?
This open loop design blows a little bigger and more free, and I think the only reason for it is the drop of solder where the tubes cross over in the other design.

Not everybody wants that - for some who like a rotary valve, the slightly more compact feel of the other wrap is preferred.
This is my understanding as well. I played some prototype valves like this while still at the company and they had a more open, wide feel.

Re: Joe Alessi

Posted: Wed Dec 18, 2019 9:39 am
by griffinben
I had a chance to talk to Steve about this - keep in mind, he worked with Joe at Edwards prior to leaving and starting his own subsequent company. While there are many things that are similar between the Edwards 396A and Shires Alessi design, there's enough different to call t a different horn. There's a lot more to design than just materials. Keep in mind that there are many King like elements on the Shires MD horns too. And the King 2B+ to Fedchock Jupiter, for that matter. It makes sense - artists develop a sound and feel concept. A horn that embodies similar elements but pushes further in different directions can yield even more refined results.

There was a lot of refinement that went on with the instrument. It was a true R&D project and has a lot of features not found on other Shires trombones before now. Some are seemingly subtle things that make a big difference.

Either way, Steve is very proud of the horn. I'll send in a review once I get a chance to play it.

Re: Joe Alessi

Posted: Wed Dec 18, 2019 1:24 pm
by sterb225
As a die hard 396 fan, I am deeply curious to play one alongside mine. My fear is that the Shires will speak to me even more readily than the 396 did - that's a conversation that my wife is not going to want to have.

Re: Joe Alessi

Posted: Tue Jun 02, 2020 6:59 pm
by Elow
Now this is a funny thread to read

Re: Joe Alessi

Posted: Tue Jun 02, 2020 9:09 pm
by ericcheng2005
sterb225 wrote: Wed Dec 18, 2019 1:24 pm As a die hard 396 fan, I am deeply curious to play one alongside mine. My fear is that the Shires will speak to me even more readily than the 396 did - that's a conversation that my wife is not going to want to have.
Diehard 396 fan gang! Might try a Shires Alessi at ITF 2021, idk

Re: Joe Alessi

Posted: Tue Jun 02, 2020 9:45 pm
by harrisonreed
ericcheng2005 wrote: Tue Jun 02, 2020 9:09 pm
sterb225 wrote: Wed Dec 18, 2019 1:24 pm As a die hard 396 fan, I am deeply curious to play one alongside mine. My fear is that the Shires will speak to me even more readily than the 396 did - that's a conversation that my wife is not going to want to have.
Diehard 396 fan gang! Might try a Shires Alessi at ITF 2021, idk
I doubt you will be able to. Being allowed to blow into a brass pipe that has been blown into by hundreds of other people at an international event seems unlikely.

Re: Joe Alessi

Posted: Tue Jun 02, 2020 9:52 pm
by ericcheng2005
harrisonreed wrote: Tue Jun 02, 2020 9:45 pm
ericcheng2005 wrote: Tue Jun 02, 2020 9:09 pm

Diehard 396 fan gang! Might try a Shires Alessi at ITF 2021, idk
I doubt you will be able to. Being allowed to blow into a brass pipe that has been blown into by hundreds of other people at an international event seems unlikely.
If you use your own mouthpiece, wouldn’t it be fine?

Re: Joe Alessi

Posted: Tue Jun 02, 2020 10:03 pm
by harrisonreed
ericcheng2005 wrote: Tue Jun 02, 2020 9:52 pm
harrisonreed wrote: Tue Jun 02, 2020 9:45 pm

I doubt you will be able to. Being allowed to blow into a brass pipe that has been blown into by hundreds of other people at an international event seems unlikely.
If you use your own mouthpiece, wouldn’t it be fine?
No.... When you breathe in moisture and air from the pipe goes into your lungs. Probably miniscule, microscopic droplets, but a lot of breaths are taken with a partial seal already on the mouthpiece.

Plus people will be dumping spit out the water key onto the floor. I dunno. I wouldn't want to be the safety or health official for that event or that venue during the current climate.

Re: Joe Alessi

Posted: Wed Jun 03, 2020 5:57 am
by timothy42b
Good point. The days of easily trying out multiple horns at large venues may be gone.

There's probably an engineering solution. Most stands are hollow. It wouldn't be that hard to build one with a reservoir at the bottom and a pump that shoots a mist of disinfectant through the tubing after each person - include a timer so every time you put it on the stand you get 15 minutes of spray. Or just disassemble, pour a couple ounces of lysol through it.

But that's easy enough for one horn, not so easy when you brought 20. And if you accidentally put an alto on the pump you built for the contra, it might launch.

Re: Joe Alessi

Posted: Wed Jun 03, 2020 6:18 am
by chromebone
There’s been lots of research showing that copper and brass alloys kill viruses on contact. Many hospitals are installing copper surfaces in critical areas.

The bigger issue will be the ability of large numbers of people being able to congregate in one place until there is a vaccine.

Re: Joe Alessi

Posted: Wed Jun 03, 2020 6:38 am
by harrisonreed
chromebone wrote: Wed Jun 03, 2020 6:18 am There’s been lots of research showing that copper and brass alloys kill viruses on contact. Many hospitals are installing copper surfaces in critical areas.

The bigger issue will be the ability of large numbers of people being able to congregate in one place until there is a vaccine.
What are inner slide tubes plated in? Brass? Nope. Are they even made of brass? If the whole tube is full of moisture and water vapor, not all of it is in contact with the brass anyways. Anyways, that's all besides the fact. If this virus still hasn't been cured, I don't see any music event being ok with testing instruments the way it is usually done at conventions.

Maybe they'll have people sign waivers lol